HGV tyre records at PMI: what the inspection sheet needs to show and the fitment log DVSA checks at audit
I passed three PMIs with a tyre sheet that only logged pressures and tread depth. Then an auditor asked for my fitment records going back 15 months. Those didn't exist.

The tyre check on a safety inspection takes about ten minutes. You walk round, stick the gauge in, write down the depths, sign it off. Job done. That's what most operators do — and most of the time, nobody says anything.
But a DVSA audit isn't a roadside stop. It's a document review. And when an examiner sat across from me in 2021 with a folder of my PMI sheets, the tyre section was the first thing she went to. Not because the vehicles weren't roadworthy. Because the records didn't show enough to prove it.
Here's what DVSA expects to find on a tyre inspection record — and what I've had to add to my own PMI sheets since then.
What the DVSA Guide to Maintaining Roadworthiness actually says
The Guide doesn't have a single checklist that says 'record these six things for tyres.' It works by setting out what a proper safety inspection must cover — and tyres are one of the core systems. The expectation is that your records prove the inspection was done properly, not just that a tyre was looked at.
That means the record needs to show what you found, not just that you found nothing wrong. Tread depth: the actual measurement, not 'OK'. Pressure: the figure, not 'checked'. Condition: visible damage, bulges, cuts, sidewall state — either noted or signed off clear.
If your PMI sheet has a box that says 'Tyres □ Pass □ Fail' and nothing else, that's not going to hold up at audit.
Tread depth: what the law says and what DVSA actually enforces
For goods vehicles over 3,500kg, the Road Vehicles (Construction and Use) Regulations 1986 — Regulation 27 — require that the tyre tread pattern is clearly visible across the central three-quarters of the tread width and around the full circumference. No groove within that area must be less than 1mm deep.
That's the legal minimum. In practice, DVSA examiners will flag anything under 2mm at a roadside check and most reputable workshops won't pass a tyre in that territory. My threshold is 3mm before I'm booking a replacement — partly because a vehicle going off for a 6-week PMI with 2.5mm on the rear offside is going to be at 1.8mm before the next inspection.
Record the actual depth. All four positions across each tyre if you're doing it properly — inside shoulder, inner, outer, outside shoulder. Most PMI sheets have space for one figure per tyre. That's technically enough. But if you're flagging a tyre as 'marginal' you want to know which part of the tread is marginal.
Pressure records: what the figure needs to be
Log the actual pressure, in bar or psi — whichever your sheet uses, just be consistent. And record what the correct pressure should be. If I write '7.5 bar' on a sheet without the vehicle's target pressure, the examiner has no way of knowing whether that figure is right or wrong.
The correct pressures come from the vehicle manufacturer or the tyre manufacturer's load/pressure chart. They vary by axle, by load, and by tyre spec. Front steer tyres on an unladen Volvo FH are different from drive tyres on a loaded Scania R-series — and your records need to reflect that, not just show a number.
Cold pressures. Always cold. Record whether the check was cold or hot, particularly if you're running a 24-hour operation and the vehicle comes in warm from a night run.
The fitment log: what most operators don't keep
This is the one that gets people. A PMI sheet records what's on the vehicle at inspection. A fitment log records what went on the vehicle, when, and from where.
When a new tyre is fitted, you should be logging:
- Vehicle registration
- Axle and position (e.g. front nearside, rear offside drive axle)
- Date of fitment
- Tyre make, size, speed rating and load index
- Whether it's new or retreaded
- Mileage at fitment (if you track mileage)
- Who fitted it — workshop name and signature
Most operators get a delivery note from the tyre supplier and file it somewhere. That's not the same as a fitment log. The delivery note tells you what you bought. It doesn't tell you what went on which vehicle, on which axle, or when.
At audit, DVSA wants to be able to trace a tyre from the PMI sheet — where they can see what's currently on the vehicle — back through previous PMIs and fitment records. If you can't show that trail, you can't prove the vehicle has been consistently maintained to spec.
Retreaded tyres: the marking requirement that catches operators out
Retreaded tyres must be marked either to BS AU 144e or UNECE Regulation 109. If the marking isn't there — or isn't legible — the tyre is illegal on UK roads regardless of its condition.
That's worth checking at PMI. Not just that the tyre looks serviceable, but that the retreading mark is visible. I note it on the inspection sheet: 'BS AU 144e marking confirmed' or 'UNECE Reg 109 marking confirmed.' One line. Takes ten seconds. Proves the check was done.
On front steer axles: DVSA's guidance is that retreaded tyres shouldn't be fitted to front steer axles on goods vehicles. That's been the position in the Guide to Maintaining Roadworthiness for years. It's guidance rather than absolute statutory prohibition, but in practice any examiner who finds a retreaded tyre on the steer axle of an HGV is going to flag it. My policy is no retreads on steer axles, full stop. It's not worth the argument.
Speed and load ratings: the spec that has to match
The tyre fitted has to be appropriate for the vehicle's maximum speed and the maximum load on that axle. Fitting a tyre with the wrong load index — even if it's the right physical size — is a modification that can affect your plating certificate.
This matters more than most operators think. A common mistake is fitting a tyre of the correct physical size but a lower speed rating than the original specification, because the replacement was cheaper or available faster. The tyre fits. The vehicle drives fine. But at a roadside check or an audit, if the tyre spec doesn't match the vehicle's operating requirements, it's a potential prohibition.
Record the speed rating and load index on the fitment record. Not just the size. '315/80 R22.5' is not a full tyre specification. '315/80 R22.5 156/150 L' is.
Disposal records: what to keep when a tyre comes off
There's no specific statutory requirement to keep records of scrapped tyres in the same way there is for, say, hazardous waste. But DVSA's implicit expectation is that you can account for what was on a vehicle and when it was changed.
My practice: when a tyre comes off, I note it in the vehicle's maintenance file — which tyre, from which position, date removed, condition at removal (wear pattern, damage type if any), and whether it went for retreading, scrapping, or spare. Takes two minutes per tyre. If an examiner questions why a tyre was replaced two inspections early, I can show it had an impact cut on the sidewall.
Waste tyres are controlled waste under UK environmental regulations. Your fitter or workshop should give you a waste transfer note when they take old tyres away for disposal. Keep those. An examiner who finds you can't account for old tyres from a fleet this size will ask questions you don't want to answer.
What the PMI sheet template needs to include
If you're using a paper PMI sheet — or a digital one through your compliance system — these are the fields your tyre section needs:
- Position (FL/FR/RIL/RIR/ROL/ROR etc.)
- Tyre size (check against plating certificate)
- Tread depth (mm, actual measurement, at least one position)
- Tyre pressure (actual and target)
- Retreaded — Y/N, and if Y: retreading mark confirmed Y/N
- Condition (cuts, bulges, sidewall damage, run-flat damage)
- Pass/Fail/Advisory with reason
If your current sheet has a single 'Tyres' box with a pass/fail tick, it needs updating. That's the kind of record that an examiner will note as 'inadequate' even if every tyre on the fleet is in perfect condition.
Retention: 15 months
PMI records — including the tyre section — must be retained for 15 months from the date of the inspection. That's the requirement from the DVSA Guide to Maintaining Roadworthiness. Not 12 months. Not 'a year or so.' Fifteen months.
And the fitment records should align with that retention period. If DVSA asks for the tyre history on vehicle X going back 15 months, your fitment log needs to cover the same window. If tyres were fitted 13 months ago and the fitment record is gone, you've got a gap you can't explain.
Store them together. Tyre fitment records in the vehicle maintenance file, alongside the PMI sheets for that vehicle. Not in a separate folder that gets archived, not in the tyre supplier's email inbox. With the vehicle's maintenance records.
What I changed after my audit
I redesigned the tyre section of my PMI sheet. It went from a single row per tyre to a grid: six positions, five columns (size, depth, pressure vs target, retreaded Y/N, condition). Added a 'fitment log' page to every vehicle maintenance file, updated every time a tyre changes. And I briefed my workshop manager to fill in both the PMI sheet and the fitment log for every tyre change — not just the job card for billing purposes.
The first audit after that, the examiner went through the tyre records for three vehicles. She didn't say much. Just 'these are what we'd expect to see.' Which, from a DVSA auditor, is about as positive as it gets.
It's not complicated. It's just doing the paperwork properly. And the paperwork is what gets you through an audit — not the condition of the tyres themselves.