Back to blog
Compliance17 November 20264 min read

The 90-hour fortnightly driving cap: how operators miss it when they're watching the weekly limit

My driver hit 56h one week, took Monday off, then worked a full second week. Technically legal on the weekly limit. I got an infringement flag. The fortnightly cap doesn't care about your weekly total.

The 90-hour fortnightly driving cap: how operators miss it when they're watching the weekly limit

When I started running tachograph analysis properly, I was focused on three numbers: 9 hours daily, 56 hours weekly, 4.5 hours before a break. Those are the ones that come up in DVSA enforcement. Those are the ones my analysis software flagged.

What I wasn't watching was Article 6(3) of Regulation (EC) 561/2006 — the 90-hour cap across any two consecutive calendar weeks. I didn't miss it badly, but I missed it. And when I started digging through 12 months of records to see how often it had been breached, I found enough flags to be uncomfortable about.

What the rule actually says

Article 6(3) of Regulation 561/2006 (now assimilated into UK law post-Brexit) is unambiguous: total accumulated driving time across any two consecutive calendar weeks must not exceed 90 hours.

It's not 90 hours per fortnight in the sense of a rolling window. It's any two consecutive calendar weeks. Week one ends, week two starts — the combined total of those two weeks must stay under 90 hours. So if you're measuring week 45 and week 46, the combined driving can't exceed 90 hours. Same for weeks 46 and 47 — that's a separate calculation.

The trap the weekly limit sets for you

The 56-hour single-week cap and the 90-hour two-week cap are different constraints. They don't overlap neatly. Here's the scenario that caught my fleet.

Driver does 56 hours in week one — absolutely legal, hits the weekly maximum. Driver does only 35 hours in week two — well under the 56-hour cap. Weekly limits: clean. Two-week total: 91 hours. Infringement.

That's the trap. If you're only running weekly analysis, you'll see two clean weeks and miss the fortnightly breach. The infringement is real, it's recordable, and DVSA's tachograph analysis software will find it.

How 90 hours adds up faster than you think

A driver running 9-hour days Monday to Friday does 45 hours in a week. A driver running four 10-hour days and three 9-hour days — which is legal under the twice-per-week extension — does 67 hours in a week. That's well under 90 across a fortnight.

But add a consistent pattern: 48 hours in week one, then another 48 hours in week two. Weekly limits are fine — 48 is under 56. Combined total: 96 hours. Clear fortnightly breach, invisible if you're only looking at weekly data.

The dangerous patterns are where a driver does slightly under the weekly limit both weeks — consistently. 48 hours + 48 hours. 50 + 42. 44 + 47. All technically legal on a weekly view. All breaching 90 hours combined.

What your analysis software does and doesn't check

Most tachograph analysis platforms check daily and weekly limits. Some check the fortnightly cap. Many don't — or they have it as an optional module that isn't turned on by default.

I found this out when I asked my software provider whether they were running the fortnightly check. Turned out it was a separate report I'd never generated. It had been off. When I ran it back through 12 months of data, I had 11 fortnightly breaches across the fleet — none of which had been flagged to drivers, none debriefed, none on file.

Check your analysis settings. If there's a 90-hour fortnightly report, generate it. If your platform doesn't have one, ask the supplier. If they tell you it's not available, that's a gap in your analysis and you need to know about it.

DVSA will find it even if you don't

When DVSA downloads a driver's card at a roadside stop, the analysis covers the full 28 days. That's four complete weeks of data — which gives them two complete pairs of consecutive calendar weeks to check for the fortnightly cap.

An infringement that your software missed because you weren't running the right report is still an infringement. DVSA's analysis doesn't care about your internal reporting gaps. It records what's on the card.

The graduated fixed penalty scheme applies. A serious fortnightly breach — consistently exceeding 90 hours — is a Category 3 or 4 offence depending on the extent of the excess. At the high end, that's a court summons rather than a fixed penalty.

Operators get fined too

This is the part that matters for the O-licence. A tachograph infringement can result in a fixed penalty notice for the driver. If the operator is found to have encouraged or permitted the breach — or simply failed to have adequate analysis in place — the Traffic Commissioner gets involved. Persistent fortnightly cap failures, unanalysed and undebriefed, suggest a systemic failure of compliance monitoring. That's the kind of finding that generates a TC letter.

The practical fix

Three things:

  • Turn on fortnightly cap monitoring in your tachograph analysis software — today, not next month
  • Build a simple weekly check: take each driver's driving total for the most recent complete week and add it to the week before. If the combined total is approaching 85 hours, flag it before the week closes
  • Include fortnightly cap in your driver debrief when it triggers — same process as a daily or weekly infringement, same 28-day debrief window, same documentation

It's also worth checking whether any existing planning patterns create structural risk. If you've got a driver whose typical week is 44-47 hours — consistently — and they don't get Monday off at the start of week two, they're regularly running close to 90 hours combined. A single busy week when both are high tips them over.

I spend about 20 minutes a month on the fortnightly check now. It's a separate report from the daily and weekly analysis, and it's worth the time. The gap I had for 12 months cost me a lot more than 20 minutes to work through when I eventually found it.

tachographdrivers hours90-hour limitArticle 6Regulation 561/2006

Run a fleet that has to keep DVSA happy?

FleetPad replaces walkaround paperwork, defect logs, and PMI records with one system the transport manager actually reads.