Back to blog
Maintenance5 November 20267 min read

HGV winter checks: the seasonal maintenance routine your PMI schedule doesn't automatically cover

Three of my fleet breakdowns last November had preventable causes. Battery, antifreeze, brake condensation. The PMI hadn't flagged any of them. Here's what I check now from October.

HGV winter checks: the seasonal maintenance routine your PMI schedule doesn't automatically cover

The PMI schedule catches defects. Seasonal preparation prevents them.

November 2019. Three callouts in ten days. A Volvo FH wouldn't start at 5am at a depot in Doncaster — battery, which had been marginal for two months but had never quite failed. An Actros lost brakes on a descent outside Sheffield — water in the air system, frozen overnight in the brake chambers. And a curtainsider with a trailer electrical fault that turned out to be a corroded plug, the kind of thing that's fine in October and fails at minus four in December.

All preventable. None flagged on the previous PMI. The inspections weren't wrong — they just weren't designed to catch seasonal vulnerabilities. That's the gap, and it's the gap that causes most winter breakdown callouts.

What's different about winter maintenance

Your PMI schedule tells you how often to inspect and what to check. It doesn't automatically tell you what changes at the start of winter. The DVSA Guide to Maintaining Roadworthiness identifies seasonal conditions as a factor in setting inspection intervals — specifically, that temperature extremes and seasonal road conditions affect wear rates. But that guidance doesn't give you a checklist for October. That part's down to you.

The difference between a summer PMI and a winter PMI isn't the paperwork — it's what you're looking for and what you're adjusting. Antifreeze concentration matters in summer too, but getting it wrong in July means your engine doesn't overheat quite as fast. Getting it wrong in January means the block cracks.

Battery condition

HGV batteries take more abuse than car batteries — the electrical loads from cab equipment, refrigeration compressors, and idle start systems are significant. A battery that tests at 60% capacity will get through most of the summer. At minus five, starting resistance increases sharply, and 60% isn't enough.

Battery test results should be on file — ideally from your last PMI before October. Drop-charge-load testing, not just a visual check. If you have a fleet of 20+ vehicles, stagger the battery replacement cycle so you're not replacing them all at once and paying for it twice.

Dual-battery systems on modern HGVs — common on vehicles with APUs or large refrigeration units — need both batteries checked. One weak cell in either battery can affect the system.

Coolant and antifreeze

Check concentration at every PMI, but specifically test it as part of your October preparation. Most fleet antifreeze should be concentrated to give protection to around minus 25°C to minus 35°C, depending on your operating area. The UK rarely hits that, but there's no benefit in running protection to only minus 10°C when a north Yorkshire winter can reach minus 12°C or lower in a prolonged cold spell.

Use a refractometer, not the old float ball type. The float method is less accurate and gives false reassurance. Refractometers are cheap and take thirty seconds per vehicle.

While you're checking coolant, check the header tank cap seal and the pressure rating. A cap that's slightly degraded may hold pressure in warm weather but fail when the system temperature cycles more dramatically in winter. They're cheap to replace and expensive to ignore.

Air brake system and moisture

This is the one that scared me most after the 2019 incident. The air braking system on an HGV uses compressed air from an engine-driven compressor. Atmospheric air contains water vapour. As the compressor runs, that moisture gets into the air system and needs to be removed — by the air dryer on modern vehicles, or manually through the drain cocks on older systems.

When temperatures drop below zero, moisture that hasn't been removed can freeze in the air lines or brake chambers, reducing braking performance or causing a valve to fail in a partially applied position. The driver may not notice until they try to slow down on a descent.

At your October check: drain all air tanks manually, inspect the air dryer and its desiccant cartridge, and note the date of the last desiccant replacement. On high-mileage vehicles, desiccant should be replaced at least annually. Check drain cocks aren't clogged — on older vehicles these are a frequent maintenance skip.

Brief drivers: if they park overnight in temperatures forecast to drop below zero, the first thing they should do in the morning before moving the vehicle is cycle the brakes a few times and check the foot pedal feels right. This isn't a replacement for proper maintenance, but it's a driver-level check that has identified frozen systems before they became incidents.

Fuel system — diesel waxing

Diesel begins to wax at around minus five to minus ten degrees Celsius, depending on the grade. This clogs the fuel filter and the injector lines. Cold filter plugging point (CFPP) is the spec you need — it's usually on the delivery documentation or the supplier's data sheet.

Most reputable fuel suppliers blend winter-grade diesel from approximately late October or early November. But if you're buying from bulk storage on-site, check your current stock's CFPP. Old summer-grade diesel sitting in a tank from September, combined with a sudden cold snap in late October, is a fleet management problem.

Diesel additives to lower the CFPP are available and worth keeping on hand. They're not a substitute for proper fuel management, but they can get you through a cold night with a tank that's slightly marginal. Dosing the tank in advance of expected cold weather is far cheaper than a truck that won't start at 4am.

Tyres

Tyre pressure drops roughly 0.1 bar per 10°C fall in ambient temperature. A tyre correctly inflated at 8 bar in September will be running at approximately 7.7 bar in January at zero degrees Celsius. That's not a catastrophic drop, but combined with a tyre that was slightly under at the last PMI, it can push you below the minimum.

Check and set pressures at the correct cold inflation standard for each vehicle, not at the ambient temperature of a warm workshop. Record the check date and pressure on the inspection sheet.

On mixed-tread tyres — where some have more residual depth than others — winter traction varies significantly. Tyres below 3mm of tread don't grip well on wet or icy surfaces even if they're legal. I pull tyres below 4mm in winter to be conservative. That's not a regulatory requirement, but a 4mm minimum is what I brief my drivers to flag as a concern on walkaround checks.

Electrical connections — trailer plugs and ABS sensors

The combination of road salt, moisture, and temperature cycling corrodes electrical connections. Trailer plugs — the multipin electrical connections between tractor and trailer — are particularly vulnerable. A poor connection on an ABS circuit will trigger a warning light and, on DVSA checking equipment, will show as an ABS fault, which is a prohibition risk.

At October preparation: inspect all trailer plug connectors, clean contact points, and apply a suitable electrical contact protector. Check ABS sensor wiring harnesses for chafing against the suspension — this is especially common on trailers that run through a lot of rough-surface depots. Replace seals on weatherproof connectors if they're showing cracks.

Windscreens, wiper blades, heating systems

Basic, but still skipped. Wiper blades that streaked all summer are a visibility hazard in sleet. Replace them before winter. Check heater function early — a cab heater that's seized in summer (because nobody used it for six months) found to be broken in November is an uncomfortable week for the driver while you source a part.

Check the washers too. Top up with a proper screenwash solution at the correct mix ratio. Plain water in the washer reservoir freezes at zero. Frozen washer lines are a minor nuisance in a car; in a cab getting salt-spray from ahead, they're a visibility issue.

Record it properly

Don't just do these checks — record them. A seasonal pre-winter inspection isn't something the DVSA Guide mandates as a named document type. But if a vehicle is involved in a winter incident and you need to demonstrate due diligence, a signed pre-winter check sheet with a date, the items checked, and the inspector's signature is evidence that you maintained the vehicle appropriately for the season.

I run a seasonal preparation sheet as an addendum to the October or November PMI for each vehicle. It takes about twenty minutes per truck and half an hour per trailer. The cost is negligible compared to a recovery callout or, worse, an incident that puts a prohibition on a vehicle and triggers an OCRS event.

Three November callouts in 2019. None in 2020, when I started doing this properly. The preparation works. It just has to happen before the first cold snap, not after.

winter-checkshgv-maintenanceseasonal-preparationantifreezebatteries

Run a fleet that has to keep DVSA happy?

FleetPad replaces walkaround paperwork, defect logs, and PMI records with one system the transport manager actually reads.