Back to blog
Compliance2 September 20266 min read

HGV width limits: 2.55m for standard goods vehicles, 2.60m for refrigerated — and where operators get it wrong

I failed a spot check because a secondhand curtainsider I'd bought had a 2.57m body. It was fine on a fridge trailer. On a tautliner, it was over the limit.

HGV width limits: 2.55m for standard goods vehicles, 2.60m for refrigerated — and where operators get it wrong

The secondhand trailer market catches operators out on width more than any other dimension. Height is visible. Length is easy to measure. Width? Most operators never check it until someone tells them they've got a problem.

I bought a secondhand curtainsider in 2019 that was 2.57 metres wide. Good trailer, well-maintained, sensibly priced. I was aware of width limits in an abstract sense, but I hadn't measured it or thought to ask. I found out it was over the standard limit when a DVSA vehicle examiner measured it during a prohibition check at Catthorpe interchange. The defect notice was uncomfortable.

Here's the rule. And it is simpler than most people assume, once you know which regulation to look at.

Regulation 8 of the Construction and Use Regulations 1986

The width limits for goods vehicles in the UK come from Regulation 8 of the Road Vehicles (Construction and Use) Regulations 1986. This is the regulation that sets the maximum width for different vehicle types.

For most motor vehicles — including tractor units, rigid lorries, vans, flatbed trailers and curtainsiders — the maximum width is 2.55 metres. That's the overall width of the vehicle body, including any permanent equipment, bodywork, and structural components. Not the cab. Not the wheels. The widest point of the vehicle.

For refrigerated vehicles — defined in the regulations as insulated vehicles with side walls at least 45 millimetres thick, designed for low-temperature cargo transport — the maximum width is 2.60 metres. That 50mm allowance reflects the space taken up by the insulation in the walls.

That's it. Two numbers. 2.55m for standard goods vehicles and trailers. 2.60m for refrigerated vehicles meeting the insulation specification in the regulations.

Why operators get confused

The confusion I see most often comes from the secondhand trailer market and from operators who run mixed fleets of refrigerated and non-refrigerated trailers.

Fridge trailers are routinely built to 2.56m, 2.58m, or even 2.60m wide, because that's permitted for a refrigerated vehicle. The problem is when a fridge trailer body is retro-fitted, re-purposed, or used as a non-refrigerated trailer. The 2.60m exemption is for refrigerated vehicles meeting the technical specification — insulated side walls of at least 45mm. If the vehicle no longer meets that definition because the refrigeration unit has been removed or the specification isn't documented, you're back to 2.55m. And 2.58m is now over the limit.

The other common issue: buying curtainsider trailers from mainland Europe. Continental European trailers are sometimes built slightly wider than the UK standard allows, because dimensions differ under European type approval in certain configurations. An operator buying a batch of ex-European curtainsiders at auction needs to check the body width, not assume compliance.

And then there's the body-on-chassis situation. Rigid body vehicles — refrigerated bodies fitted to 7.5-tonne or 18-tonne chassis — sometimes have bodies that were built for a wider chassis than the one they're now sitting on. The overall width might be fine, or it might not. It needs to be measured.

What counts as width for measurement purposes

Width is measured at the widest point of the vehicle body, including any permanent structural projections. Mirrors are excluded from the width measurement under a separate provision — they're assessed separately under mirror requirements. But load restraint rails, roller shutter guides, body corner guards and similar permanent fittings that increase the width of the body itself are included.

Side skirts on rigid vehicles cause confusion here. Aerodynamic side skirts that project beyond the body line are counted in the width measurement if they're permanently attached. If they fold or are removable for loading, that's a different calculation depending on how they're designed.

If you're buying trailers secondhand, measure the width at the body before you commit. Not after you've signed. Measure the body at its widest point — often the rear corners, especially on curtainsiders with reinforced rear stanchions.

Conditioned containers and swap bodies

Regulation 8 also gives the 2.60m allowance to conditioned containers — sealed insulated containers used for temperature-controlled transport across different modes. These are distinct from standard refrigerated trailers but operate under the same width allowance. Swap bodies designed for temperature-controlled transport that meet the insulation specification can also use the wider limit.

This matters if you're running intermodal operations or collecting loaded containers at ports or rail terminals. The container itself may be 2.60m wide, which is permissible, but the vehicle carrying it needs to comply with the overall width limits for the combination. A container that sits entirely within the vehicle body width is fine. One that overhangs isn't — that would make it an abnormal load requiring a different category of authorisation entirely.

DVSA enforcement and what they measure

Width isn't the first thing DVSA examiners check at a roadside stop. They're typically looking at load security, brake performance, tyre condition and documentation first. But during a detailed vehicle examination — which follows from any serious prohibition or from a targeted enforcement operation — width gets measured.

A vehicle found to exceed the permitted width is a construction and use offence. That's a fixed penalty for the driver and a potential prohibition on the vehicle. It also goes on your OCRS record as a vehicle defect found at the roadside, which affects how often your fleet gets targeted for checks.

The prosecution goes to the operator, not just the driver, because the obligation to maintain the vehicle in compliance with construction and use requirements sits with the operator under the operator's licence undertakings. An operator who knowingly runs an oversized vehicle, or who doesn't have systems in place to catch it, has a harder conversation with the TC if it becomes part of a pattern.

Checking your fleet right now

If you've never actively checked the body widths on your trailers, do it. It takes about 20 minutes with a tape measure. Start with any secondhand trailers bought in the last five years, any refrigerated or ex-refrigerated bodies, and any trailers sourced from outside the UK.

Check the vehicle registration document (V5C) and any type approval documentation. The body width should be stated. If the stated width is over 2.55m and the vehicle isn't a refrigerated vehicle meeting the Regulation 8 definition, you have a problem. If the stated width is between 2.56m and 2.60m and it is a refrigerated vehicle, measure the insulation — the wall thickness needs to be at least 45mm to qualify for the exemption.

Document what you find. If you've got a trailer fleet with a mix of compliant and non-compliant vehicles, you need to know which is which before your next DVSA inspection. The fact you didn't know is not a defence — the compliance obligation sits with you as the operator.

What about extending an existing trailer?

I've heard of operators — usually in the agricultural sector, but occasionally in general haulage — who've had trailer bodies widened by a bodybuilder to carry more payload. This is technically possible but puts the trailer outside its original type approval. A trailer that has been structurally modified needs to go through a vehicle approval process to confirm it still meets construction and use requirements under the modified specification.

Running a structurally modified trailer without updated approval documentation is a problem waiting to happen. If DVSA finds a trailer that's been modified and there's no documentation to show it's compliant in its current configuration, the vehicle comes off the road while that gets resolved.

Get it tested, get the paperwork, do it properly. The cost of a structural modification done right is significantly less than the cost of an improvement notice, a prohibition, and a public inquiry.

HGVWidth LimitsConstruction and Use RegulationsRefrigerated

Run a fleet that has to keep DVSA happy?

FleetPad replaces walkaround paperwork, defect logs, and PMI records with one system the transport manager actually reads.